Product description:
Acrylic Resin Polyester Resin Production Line
Resin reaction kettle is the key equipment for producing unsaturated polyester resin, phenolic resin, epoxy resin, ABS resin and paint.
Resin complete equipment is composed of reaction pot, vertical fractionation column, horizontal condenser, water storage device,
oil spill tank, pipeline (to thin kettle), etc., a full set of equipment and material contact department...
Fracture:
Resin complete set of equipment is composed of reaction pot, vertical fractionation column, horizontal condenser, water storage device, oil spill tank, pipeline (dilute kettle), etc., the whole set of equipment and material contact part of the selection of stainless steel.
Unsaturated Polyester Resin Reactor Plant Polyester Resin Equipment Chemical Resin Polyurethane ReactorIt IS THE KEY EQUIPMENT FOR THE production of unsaturated POLYESTER resin, alkyd resin, phenolic resin, epoxy resin, ABS resin and paint. The complete set of equipment is composed of reaction kettle, vertical fractionation column, horizontal condenser, water storage device, oil spill tank, pipeline (for dilute kettle), etc. The contact part between the complete set of equipment and materials is made of stainless steel
Appliance:unsaturated polyester reasin, allkyd resin,phenolic resin,abbs resin and paint key facility.
Machine Constraction:
Full set facility combine via reactive tank,vertical distilled polar, horizontal type condensation,water saving machine, oil spill groove,tube pipeline ect combine, full set facility and material touch part all adopt to sus304 material.
UPR(unsaturated polyester resin):large volume; high-speed of reaction and well distributed heat conductivity, easy operation and low cost.
UPR plant is the crucial equipment used to produce unsaturated polyester resin. The plant consists of reaction pot, vertical still,horizontal condenser, water storage tank, oil spilling groove, pipeline (double rare). The contacted part of the plant and material is made of stainless steel.
Features of unsaturated polyester resin plant.
1) Capacity: 50~20000Liters.
2) Jacket and coil pipe are used together for heating and cooling.
3) High-speed reaction and well distributed heat conductivity.
4) Consistent resin quality.
5) easy operation and low cost.
Resin complete production line includes:
1.key reactor
2.vertical distillation column
3.vertical condenser
4.horizontal condenser
5.dispersion reactor
6.oil water separator
7.vacuum system
Product list:
1.unsaturated polyester resins
2.phenolic resin
3.epoxy resin
4.alkyd resin
5.ABS resin, etc.
Supply range:
1. adhesive glue production line
2. Unsaturated resin production line
3. Acrylic resin production line
4. Urea-formaldehyde resin production line
5. Polyurethane resin production line
6. Epoxy resin production line
Flow chart-one
Prepare material-Add P1,P2-Collect samples-test water quantity(≥0.1% temperature increase,remove water;)≤0.1%--add change character MP1--draw vacuum--increase temperature 70degree(reaction 30minute)--increase temperature 75degree.(reaction 30minute)---increase temperature 80-85degree.(reaction 60minute)--increase temperature 87-92degree.(reaction 120minute)--collect samples test NCO(below standard-rework)-collect samples test NCO (up to stand)--reduce temperature--discharge-packing
Flow chart-two
Prepare material--add part of PS and auxiliaries--disperse--grinding mix color--(Add left P3)B tank reactive--draw vacuum--increase temperature to 105-110degree(reactive 120minute)--warm keep reactive--collect samples(below stand-rework)--reduce temperature(qualified)--feeding material--packing
Second part:B group production flow chart and requirement.
1. Mixed grinding
According to the raw materials in the formula, prepare P4, chain extender, oil soluble color paste, ultraviolet absorbent, antioxidant, etc. into the dispersion cylinder, and stir with the high-speed dispersion machine in the paint workshop. After mixing well, use a sander to grind the mixture to a fineness less than 15μm.
2. P4 pumping
Start the vacuum pump to vacuum, weigh the mixed polyether P4 through the electronic pound, and send the resin to the reaction kettle B through the vacuum of negative pressure.
3. Heat up and stir
Start the vacuum pump to vacuum. Make the vacuum in the reactor to be above -0.95MPa, start the program on the man-machine interface, and automatically control the temperature, time and stirring according to the program when the vacuum degree reaches the process requirements (temperature rise to 105ºC-110ºC, heating and holding vacuum stirring for 120 minutes).
4. Cool Down
Open the water inlet valve of the condenser of kettle B, cool oil circulates, and the oil pump sends the cold oil to the jacket of kettle B to replace the hot oil in the jacket, until the temperature required for discharging material is below 70ºC.
5. Add catalyst
Stir in the catalyst for 30 minutes and let cool to room temperature.
6, viscosity, total hydroxyl value detection
The operator takes samples from the sampling port for inspection, and tests the viscosity and total hydroxyl value.
7. Feed
After qualified, place the packing drum on the packing scale, replace the air in the packing drum with nitrogen, manually open the discharge valve at the bottom of reaction kettle B and discharge the material. When the weight in the packing drum reaches the rated weight, close the discharge valve, the weighing error is less than 1%, and seal the nitrogen during packaging.
8. Viscosity and NCO detection
The operator takes samples from the sampling port for inspection.
9. Cool Down
After the NCO test is qualified, open the inlet valve of the condenser of reactor A to cool the oil. The oil pump will send the cold oil to the jacket of reactor A to replace the hot oil in the jacket until the temperature required for discharge packaging is reached.
10. Feed
Place the packing bucket on the packing scale, replace the air in the packing bucket with nitrogen, and manually open the discharge bottom valve of the reaction kettle A. Close the discharge valve, the weighing error is less than 1%, and seal the nitrogen when packing.
11. Packaging
Check whether the product is consistent with the package, paste the certificate of qualification in the designated location,
12. Storage
Place finished products neatly in finished products area.
Prepare material-add part P4 auxiliary--disperse--grinding adjust color--add left P4,draw vacuum,load material--draw vacuum,start B reactive tank reaction--increase temperature 105-110degree(reaction 120minute)--reduce temperature to below 70degree,add catalyst(reaction 30minute)-collect samples test--(below stand-rework)--reduce temperature(qualified)--feeding material--packing
Overview of reactor
Purpose and characteristics of the reactor
The reactor has the advantages of high temperature resistance, corrosion resistance and strong production capacity.
Ii. Structural points of the reactor
The reaction pot is composed of pot body, pot cover, stirrer, heating jacket, supporting and driving device, shaft sealing device, etc.
The pot body and the pot cover are connected by sealing flange, the lower part of the pot body has feeding hole, the pot has a stirrer, the pot cover open feeding, stirring observation, temperature and pressure measurement, steam extraction fractionation, safety vent and other process tube holes.
On the heating jacket of the reaction kettle, there are pipe holes for temperature measurement of oil and exhaust (steam), vent steam valve, electric bar and so on.
Due to the different production technology and operating conditions, users can contact our factory for different requirements on pot cover technology such as opening, mixing type (slurry type, anchor type, frame type, screw type, etc.), supporting type (hanging type or bearing type) and packing sealing.
The reactor is mainly used for hydrolysis, neutralization, crystallization, distillation, evaporation, germicidal storage and other production processes in medicine, chemical industry, food, natural flavoring, food additive and light industry.The reactor can be made of SUS304, SUS316L and other stainless steel materials.Agitator has anchor type, frame type, paddle type, turbine type, scraper type, combined type, rotating mechanism can adopt cycloid needle wheel reducer, can meet the special requirements of various materials.Stepless speed reducer, sealing device can use mechanical seal, heating cooling can use jacket, half pipe, coil, Miller plate and other structures, heating means of steam, electric heating, heat conduction oil, to meet the acid resistance, high temperature resistance, wear resistance, corrosion resistance and other different working environment process needs.Can be designed and manufactured according to the requirements of customer process.
Description of the main structure of the reactor
The reactor is mainly composed of the inner tank, jacket, agitator and supporting seat (the thermal insulation structure can be adopted according to the technological requirements).
1. The inner tank is made of stainless steel (SUS304, SUS316L or SUS321) as required by the process. The inner surface is treated with mirror polishing.
2. The jacket shall be made of stainless steel (SUS304) or carbon steel (Q235-B) as required by the process.
3. Suitable diameter to height ratio design, customized mixing device as required;The stirring shaft seal adopts the pressure-resistant sanitary mechanical sealing device to maintain the working pressure in the tank and prevent the material leakage in the tank from causing unnecessary pollution and material loss.
4. The supporting type shall adopt the hanging ear type or the landing leg type according to the operation requirements.
Flow chart:
Other reactor
Audited Supplier 
){kind=link}